Website

They are making a number of great pointers regarding A Step-by-Step Guide to Installing a Bathtub as a whole in this post followed below.

Installing a bath tub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and also often, tiling skills. Changing an old bath tub with a new one is also a moderately tough project. If the old bathtub is easily available, the task can relocate immediately; if you need to open a wall surface to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either instance, the task is within a house handyman's skills, although you will certainly require a helper to leave the old bathtub and set in the brand-new one. Ensure you have qualified on your own for the task and fit attempting it. Rather than employing a specialist to take over a halfway-completed project, it is better to take into consideration using one before you start. Possibilities are you may need a professional plumber to make tube connections.
This short article will certainly aid you set up a brand-new tub in your restroom if you have already purchased a new tub and do not require to change the plan of your previous water supply pipelines.
Your tools and product list should make up the following:

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Getting ready for the Installation

First of all, the sustaining framework supplied with the bath ought to be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to make certain that if the tap includes a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps unit to avoid strain on the bathtub.
Fit the versatile tap connectors to the bottom of both faucets using 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be suited its last position.

Removing Old Taps

If you need to replace old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, activate the taps to drain pipes any water remaining in the system. The procedure of removing the existing faucets can be fairly troublesome as a result of the limited gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a cloth prepared for the staying water that will come from the pipes. Once the supply pipes have been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from turning throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old securing compound.
Prior to carrying on to fit the new faucets, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.

Setting up the Bathtub

Utilizing the two wood boards under its feet, place the bathtub in the required setting. The wood boards are useful in evenly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 small factors.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by checking the spirit level as well as adjusting the feet on the tub till the spirit level reviews degree.
To set up faucets, fit all-time low of the outermost versatile faucet connector to the proper supply pipe by making a compression join; after that do the exact same for the various other tap.
Turn on the supply of water and check all joints as well as brand-new pipework for leakages as well as tighten them if required. Fill the tub as well as likewise examine the overflow electrical outlet and also the regular outlet for leaks.
Finally, deal with the bath paneling as described in the producer's user's manual. Tiling and also sealing around the bath tub ought to wait up until the bathtub has been used at least once as this will certainly resolve it right into its final setting.

Fitting New Touches

If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washers remain in location in between the tap and also the sink. Secure the faucet in position with the maker offered backnut. When the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type must be linked to the tap finishes first, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.

Tiling Around the Tub

In the location where the bath fulfills the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to split a stiff seal, causing the water to permeate the wall in between the bathroom and also the tiling, bring about difficulties with moisture and also possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the tub with water prior to securing, to enable the movement experienced when the tub remains in use. The sealant can fracture rather very early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily offered on the market. It is advisable to fit the ceramic tiles using waterproof or waterproof glue and cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

We had been shown that article about Installing A Bathtub from an associate on another web blog. Sharing is good. Helping people is fun. Thanks so much for taking the time to read it.

Trusted service? Dial!